45 -- Hardware Plumbing Supplies for Water Tank Installation

VENDORS PLEASE NOTE CLARIFICATION OF DESCRIPTION FOR THE FOLLOWING ITEMS: Line Items 28 and 29: SDR rating: 11 at 160 psi Line Item 30 - Schedule of pipe = 40; Perforation: 4 holes per ring pattern, 5 inches between rings 1/2 inch holes. There is no change in response due date for quotes. This is a combined synopsis/solicitation for commercial items prepared in accordance with the format in Subpart 12.6 as supplemented with additional information included in this notice. This announcement constitutes the only solicitation; proposals are being requested and a written solicitation will not be issued. This is a request for quotations No. AG-02NV-S-06-0074. The solicitation document and incorporated provisions and clauses are those in effect through Federal Acquisition Circular 2005-12. The Forest Service intends to install a water tank in a campground on the Salmon-Challis National Forest on or around October 6. The above items are supplies needed for this installation. Delivery: On or before October 6, 2006. Destination: Challis Ranger District, Highway 93, Challis, ID 83226. Contract line item numbers, description, quantities and unit of measure follows. ITEM NO DESCRIPTION QUANTITY UNIT AMOUNT TOTAL AMOUNT 1 1? Ball Valve - Ball valve - Bronze 400 PSI, model B600 as manufactured by Watts Regulator or an approved Equal. 3 EA $________ $________ 2 1? Gate Valve - Gate Valves - Gate valves shall be bronze, solid wedge disc, non-rising stem, threaded ends, 150 psi, Powell Valve Fig. 512, as manufactured by Powell Company, Cincinnati, Ohio, or No. 437, as manufactured by the Crane Company, Chicago, Illinois, or an approved equal. 3 EA $________ $_________ 3 1? Malleable Iron Union - The union shall be female type, malleable iron, 150 pound, with ground brass to iron seat, as manufactured by the Crane Co., Chicago, Illinois, or approved equal. 8 EA $________ $________ 4 1? Globe Valve - The globe valve shall be threaded, 150 psi, union bonnet, renewable composition disc with integral seat, with bronze body, Powell Fig. 150 as manufactured by Wm. Powell Company, Cincinnati, Ohio, 513-852-2000, www.powellvalves.com, or No. 7, as manufactured by the Crane Company, Chicago, Illinois, or an approved equal. 2 EA $________ $________ 5 ?? Smooth-nosed Sample Tap. Brass, 1/2-inch hose bib with male inlet and smooth-nosed outlet. Model number P/N 301PE as manufactured by Arrowhead Brass, or an approved equal. 3 EA $________ $_________ 6 1? Wye Strainer. The Y-strainer shall be 125 psi, or greater, have a semi-steel or bronze body with screwed ends, have a brass plug in the blow-off connection, and shall have a removable stainless steel, 20 mesh screen. The Y-strainer shall be a Style B or F, as manufactured by the O. C. Keckley Company, Skokie, Illinois, 800-532-5539, www.keckley.com, or Model 777S as manufactured by the Watts Regulator Company, 815 Chestnut Street, North Andover, MA 01845-6098, phone 978-688-1811, www.wattsreg.com, or an approved equal. 3 EA $________ $________ 7 ?? Brass Gauge Cock. The gauge cock shall be a 1/4-inch diameter brass cock, Ashcroft Model 1095 as manufactured by Dresser Industries, Inc., or an approved equal. 2 EA 8 2? Pressure Gauge. Pressure Gauge shall be a 2-inch diameter gauge or larger with range of 0 - 100 psi. The movement shall be fabricated of brass and the case of steel. The gauge shall be bottom mounting with 1/4-inch diameter National Pipe Threads. The gauge shall be Ashcroft Model 1005 as manufactured by Dresser Industries, Inc., 250 East Main Street, Stratford, CT 06614-5145, phone 203-378-8281, or an approved equal. 1 EA $________ $__________ 9 2? Pressure Gauge. Pressure Gauge shall be a 2-inch diameter gauge or larger with range of 0 - 200 psi. The movement shall be fabricated of brass and the case of steel. The gauge shall be bottom mounting with 1/4-inch diameter National Pipe Threads. The gauge shall be Ashcroft Model 1005 as manufactured by Dresser Industries, Inc., 250 East Main Street, Stratford, CT 06614-5145, phone 203-378-8281, or an approved equal. 1 EA $________ $__________ 10 ?? Hose Bib w/Vacuum Breaker. The hose bib shall be rough brass finish with male inlet and 3/4" hose thread outlet, as manufactured by Arrow Head Brass Products, the Chicago Faucet Company, or an approved equal. The hose bib shall be equipped with a hose vacuum breaker, Watts Model #8A, as manufactured by the Watts Regulator Company, www.wattsreg.com, or an approved equal. 3 EA $________ $_________ 11 1? Water Meter ? The water meter shall meet the requirements of AWWA C700, be a displacement-type and have a bronze main case. Flow shall register in gallons. The water meter shall be a 1-inch SR, as manufactured by Sensus Metering Systems, P.O. Box 487, 450 N. Gallatin Ave., Uniontown, PA 15401, 1-800-638-3748, www.sensus.com, or an approved equal. 3 EA $________ $_________ 12 Pressure Regulating Valve - The pressure regulating valve shall be Watts Series 223 as manufactured by Watts Industries, Inc., of Houston, Texas, or an approved equal. The pressure regulating valve shall be of the size and have pressure adjustment for an outlet pressure of 50 PSI and inlet pressure of 160. 1 EA $________ $_________ 13 Pressure Regulating Valve - The pressure regulating valve shall be Watts Series 223 as manufactured by Watts Industries, Inc., of Houston, Texas, or an approved equal. The pressure regulating valve shall be of the size and have pressure adjustment for an outlet pressure of 50 PSI and inlet pressure of 135. 1 EA $________ $_________ 14 2? GSP Vent. The vent shall be a Morrison Bros. tee vent, Figure No. 155, as supplied by F. W. Jones, Inc., of Murray, Utah, or an approved equal. The tee vents shall be fitted with No. 24 and No. 4 galvanized steel wire screens. 3 EA $________ $_________ 15 Water Hammer Arrestor. Series 15 as manufactured by Watts Regulator Company or an approved equal. 3 EA $________ $_________ 16 2? HDPE to 2? GSP Connector. Only fittings produced by the same manufacturer as the pipe shall be used, and they shall have the same pressure rating as the pipe. Transition fittings for making connections to galvanized steel pipe shall be approved fittings as recommended by the pipe manufacturer. The steel pipe part of transition fittings shall be coated with epoxy paint approved for use in public water supplies. Ribbed steel inserts with stainless steel clamps are not approved for HDPE pipe. 11 EA $________ $_________ 17 1"X2" GSP Bell Reducer 6 EA $________ $__________ 18 1" GSP 90o Elbow 2 EA $________ $__________ 19 2" GSP 90o Elbow 1 EA $________ $_________ 20 2"X2"X2" GSP Tee 5 EA $________ $_________ 21 1"X1"X1/2" Galv. Tee 3 EA $________ $_________ 22 1"X1"X1" Galv. Tee 3 EA $________ $_________ Steel pipe and fittings shall be Schedule 40 galvanized, threaded, and conform to ASTM A53 and ASTM A338. Steel Pipe and Fittings - Steel pipe and fittings up to and including 2 inches in diameter shall be threaded and coupled, galvanized, and conform to the requirements of ASTM A 53. Steel pipe and fittings larger than two inches in diameter shall be furnished as specified on the drawings. Fittings such as manufactured by Rockwell International, flanged joints and fittings, and pipe other than screwed galvanized steel will be specified on the drawings. 23 2" HDPE 90o Elbow 20 EA $_______ $__________ 24 3" HDPE 90o Elbow 20 EA $_______ $__________ 25 3"X3"X2" HDPE Tee 3 EA $_______ $__________ 26 3"X3"X3" HDPE Tee 6 EA $_______ $__________ 27 2"X2"X2" HDPE Tee 10 EA $_______ $__________ 28 2" HDPE 250 LF $_______ $__________ 29 3" HDPE 150 LF $_______ $__________ All pipe and fittings shall be new, and unused. All materials must meet ANSI/NSF 61. The pipe and fittings used for the waterlines shall conform to the following applicable specifications: High Density Polyethylene (HDPE) Plastic Pipe With Heat Fusion Joints - High Density Polyethylene (HDPE) plastic pipe shall be PE 3408 as defined in ASTM D 3035 (outside diameter controlled) with a minimum cell classification of 345434C in accordance with ASTM D 3350. All polyethylene plastic pipes shall bear the logo of NSF International, "NSF-PW." 30 3? PVC Perforated. Polyvinyl Chloride (PVC) Plastic Pipe and Fittings - All PVC pipe must meet requirements as set forth in ASTM Specification D 2241, D 1785. All material must meet ASTM Specification D 1784. All PVC pipe shall bear logo of NSF International, "NSF-PW." 150 LF $_______ $__________ 31 3? PVC 90 degree elbows. - Polyvinyl Chloride (PVC) Plastic Pipe and Fittings - All PVC pipe must meet requirements as set forth in ASTM Specification D 2241, D 1785. All material must meet ASTM Specification D 1784. All PVC pipe shall bear logo of NSF International, "NSF-PW." 13 EA $_______ $__________ 32 3? PVC tees - Polyvinyl Chloride (PVC) Plastic Pipe and Fittings - All PVC pipe must meet requirements as set forth in ASTM Specification D 2241, D 1785. All material must meet ASTM Specification D 1784. All PVC pipe shall bear logo of NSF International, "NSF-PW." 4 EA $________ $__________ 33 2? Curb Valve. Poly valves shall have the same SDR number as the HDPE pipe line ordered above and shall be NSF approved. Valves shall conform to AWWA C906 or of similar quality. Valves shall be Poly-Water valves as manufactured by Nordstrom Audco Inc. of Sulphur Springs, Texas, or an approved equal. 10 EA $________ $_________ 34 Ploly 2? Valve Box. Curb and Valve Boxes - Each curb box shall be furnished with a 4' stationary key rod that will fit a key. Valve box lids shall be labeled ?WATER.? All boxes, depending on their size and service, shall be the following lengths (two 8' and eight 6'). Curb Boxes for 2-Inch through 6-Inch Valves - Boxes shall be sliding or screw type, Buffalo pattern, with a 5 ? inch shaft. Valve boxes shall be Series 500 Plastic Boxes as manufactured by Bingham and Taylor of Culpeper, Virginia, or an approved equal. 10 EA $________ $_________ 35 Poly 2" Valve Key. 4 foot 1 EA $________ $__________ 36 Poly 2? Valve Key. 2 foot. 3 EA $________ $__________ 37 Suction Strainers (6?). Galvanized Steel Suction Strainer with 3/8" Strainer holes, with a 6" diameter and to fit 2" pipe 6 EA $________ $__________ 38 Suction Strainer (7?). Galvanized Steel Suction Strainer with 3/8" Strainer holes, with a 7" diameter and to fit 3" pipe 3 EA $________ $__________ 39 Accessible Hydrant. Frostproof, Anti-Pollution Hydrant ? The hydrant shall meet the ASSE 1057 Sanitary Yard Hydrant Standard. The hydrant shall be of the necessary bury depth, as manufactured by Hoeptner Perfected Products (Freezeflow), 7796 Oak Springs Circle, Gilroy, CA 95020, phone 408-847-7615, www.freezeflow.com, or an approved equal. The hydrant shall be a Freezeflow Executive model with ADA handle. 1 EA $________ $_________ The provisions at 52.212-1, Instructions to Offerors?Commercial, apply to this acquisition. Addenda to 52.212-1: The Government will evaluate all quotes submitted before contract award. The Government will evaluate quotes based on lowest price, technically acceptable items. Quoters are to complete a copy of the provision at 52.212-3, Offeror Representations and Certifications?Commercial Items, with their quote (http://www.arnet.gov/far/current/html/52_212_213.html). In lieu of including a copy of 52.212-3, offerors may have completed a copy of the provision on the online representations and certifications website (ORCA) through the Central Contractor Registrar. Clause 52.212-4, Contract Terms and Conditions?Commercial items, applies to this acquisition. Clause 52.232-5, Contract Terms and Conditions Required to Implement Statues or Executive Orders?Commercial items, applies to this acquisition. The following clauses cited in the clause are applicable to the acquisition: 52.219-6, 52.219-27, 52.222-3, 52.222-19, 52.222-21, 52.222-26, 52.222-36, 52,225-1, 52.232-33. Quotes are due by 12 Noon MST, on September 18, 2006, at IDAWY Acquisition Service Center, 1405 Hollipark Drive, Idaho Falls, ID 83401, or to fax number 208-557-5829. Quoters should call to confirm receipt of fax at 208-557-5775. Point of Contact Diane Kohler, Purchasing Agent, Phone (208) 557-5775, Fax (208) 557-5829, Email [email protected]. Karlotta Parry, Phone (208) 557-5773, Fax (208) 557-5829, Email [email protected].