The Government intends to solicit and negotiate with only one source, Winton Machine Co., 3644 Brunette Road, Suwanne, GA. 30024-2191. The procurement will be conducted on a sole source basis in accordance with the statutory authority of Section 4202 of the Clinger-Cohen Act of 1996 for one (1) each angle measuring machine, one (1) each Accessory Kit and one (1) each Tooling that shall be compatible with the Winton RD-30 computerized tube bender. The Agency intends to enter into a firm-fixed-price, supply-type contract with Winton Machine Company. The basis for restricting competition is that the tooling bend dies, clamp dies and mandrel Rods shall be compatible with the Winton RD-30 computerized tube bender. Activity has a Winton RD-30 computerized tube bender and needs additional tooling that is compatible with their machine. Winton Machine Company is believed to be the only source that can provide additional tooling compatible with the Winton RD-30 computerized tube bender. Procure from another source would involve substantial duplication of cost and unacceptable delays as other vendors would be required to obtain engineering specifications to manufacture tooling compatible with the Winton RD- 30 computerized tube bender. Specifications are listed on https://doc.campbell.army.mil . NAICS code for this procurement is 333513 and the small business size standard is 500 employees. This sole source requirement will be procured under Simplified Acquisition Procedures and Other Than Full and Open Competition, and awarded on an unrestricted basis. THIS NOTICE IS NOT A REQUEST FOR COMPETITIVE OFFERS and solicitation will not be issued; however, any firm that believes it can meet the requirements may give written notification to the Contracting Officer within 7 days from the date of the publication of this synopsis. Supporting evidence must be furnished in sufficient detail to demonstrate the ability to comply with the requirements listed. Responses received will be evaluated; however, a determination by the Government not to compete the proposed procurement based upon responses to this notice is solely within the discretion for the Government. If no responses are received, the Government will proceed with the sole source negotiation with Winton Machine Company Co., 3644 Brunette Road, Suwanne, GA. 30024-2191. Responses are due by 11 September 2008, 5:00 p.m. (CST). Responses shall be submitted via e-mail to the following address:
[email protected] or faxed responses will be accepted at (270) 798-7548. Telephone requests or inquires will not be accepted. The points of contact are Mr. Eric Boston, 270-798-7811,
[email protected]. Horizontal measuring table Quantity 1 Each FFP FOB Destination Horizontal measuring table, two arms, Rotational motion is guided by high strength lubricated bearing, Linear motion guided by linear ball, High resolution encoder, Digital Readout, Reset Button. Measuring Range, Bend Angle -30 degree to 220 degree Accuracy 0.040 Repeatability 0.040 Displayed Bend angle 0.1 degree increments Dimensions 12 IN x12 IN x4 IN high Power input 120v ac, 50/60HZ, 220 V AC available Accessory Kit: FFP FOB Destination One set of taller static & dynamic arms and 1 set of longer static & dynamic arms. All arms have tapped holes in them to make the AM40 more useful. Tooling Quantity 1 Each All Measurements are fractions of an inch FFP FOB Destination Bend Die .250 OD x 750 CLR Grip Length .500 Bend Die .250 OD x 1.00 CLR Grip Length .500 Bend Die .250 OD x 1.250 CLR Grip Length .500 Bend Die 250 OD x 1.50 CLR Grip Length .500 Bend Die .250 OD x 1.75 CLR Grip Length .500 Clamp Die.250 OD Overall Length .500 Bend Die .375 OD x 1.00 CLR, Grip Length .500 Bend Die .375 OD x 1.250 CLR Grip Length .500 Bend Die .375 OD x 1.50 CLR Grip Length .500 Bend Die .375 OD x 1.750 CLR Grip Length .500 Bend Die .375 OD x 2.00 CLR Grip Length .500 Clamp Die .375 OD, Overall length .500 Bend Die .500 OD x 1.250 CLR, Grip Length .750 Bend Die .500 OD x 1.500 CLR, Grip Length .750 Bend Die .500 OD x 1.75 CLR, Grip Length .750 Bend Die .500 OD x 2.00 CLR, Grip Length .750 Clamp Die .500 OD Overall Length .7250 Bend Die .625 OD x 1/50 CLR, Grip length .750 Bend Die .625 OD x 1.750 CLR, Grip Length .750 Bend Die .625 OD x 2.00 CLR, Grip Length .750 Bend Die .625 OD, Overall length .750 Bend Die .750 OD x 2.00 CLR Grip Length 1.125 Bend Die .750 OD x 2.250 CLR Grip Length 1.25 Bend Die .750 OD x 2.500 CLR Grip Length 1.125 Clamp Die.750 OD Overall length 1.125 Bend Die 1.0 OD x 3.00 CLR, Grip Length 1.250 Bend Die 1.0 OD x 3.250 CLR, Grip Length 1.250 Clamp Die 1.0 OD x overall Length 1.250 Mandrel Rod (Solid) Quick disconnect style for .250 OD (4-40 mandrel and thread) Mandrel Rod (Solid) Quick disconnect style for .375 OD (10-24 mandrel and thread) Mandrel Rod (Solid) Quick disconnect style for .625 OD (5/16- 18 mandrel and thread) Mandrel Rod (Solid) Quick disconnect style for .750 OD (3/8-16 mandrel end thread) Mandrel Rod (Solid) Quick disconnect style for 1.0 OD (5/8-11mandrel end thread) Bend Die .375 OD x 2.00 CLR, Grip Length of 1.125 Bend Die .625 OD x 1.50 CLR, Grip Length of 1.875 Bend Die .625 OD x 1.75 CLR, Grip Length of 1.875 Bend Die .750 OD x 1.75 CLR, Grip Length of 2.25 Bend Die .750 OD x 2.00 CLR, Grip Length of 2.25