Scrap Railroad Wheels

This is a combined synopsis / solicitation for 30 each type A, 103 each type B, and 50 each type C scrap railroad wheels. Type A - shaft flame cut or better 42 inches from inside of wheel, cut should be level +/- one half (1/2) inch, approx weight is 1100 pounds, maximum shaft diameter at cut not to exceed seven and one-half (7-1/2) inches, axel must be flush cut on bottom to allow wheel to sit flat on a flat surface, wheel axel shaft shall contain a drilled hole of one and nine-sixteenths (109/16) inches diameter through the center of the shalf with the hole centered +/- one-quater (1/4) inch, two and one-half (2-1/2) inches below the cut edge of the axel, and parallel to the base to the wheel, the hole shall allow for insertion of a fourteen (14) inch long, one and one-half (1-1/2) inch diameter steel rod completely through the shalf, the knuckle on the shalf shall not exceed a diameter that allows the wheels specified as thpe B and C to rest directly on the wheel at the base of the shalf. Type B - wheel with axel pressed out, minimum hole dismeter eight and one-fourth (8-1/4) inches, with a weight of 840 pounds, +/- 30 pounds. Type C - wheel with axel pressed out, minimum hole diameter of eight and one-fourth (8-1/4) inches eith a weight of 710 pounds, +/- 30 pounds. All items FOB NOAA, PMEL. 7600 Sand Point Wy NE, Seattle, Wa 98115, all items delivered to this site on flatbed truck or dunp truck, ( NOTE: items will not be unloaded from an enclosed van). Provide you price quote to Melvin Fondue at fax number 206-527-7177 or email at [email protected] . This is a simplified acquisition with an estimated value of less than $100,000 The following provisions and clauses shall apply to this solicitation and resultant award. The provisions and clauses may be downloaded at http://www.acqnet.gov/far 1. 52.213-4 TERMS AND CONDITIONS--SIMPLIFIED ACQUISITIONS (OTHER THAN COMMERCIAL ITEMS) (APR 2005) 2. 52.243-1 I CHANGES--FIXED-PRICE (AUG 1987)--ALTERNATE I (APR 1984) 3. 52.204-6 DATA UNIVERSAL NUMBERING SYSTEM (DUNS) NUMBER (OCT 2003) 4. 52.204-7 CENTRAL CONTRACTOR REGISTRATION (OCT 2003) 5. 52.204-8 ANNUAL REPRESENTATIONS AND CERTIFICATIONS (JAN 2005) 6. 52.219-1 SMALL BUSINESS PROGRAM REPRESENTATIONS (MAY 2004) 7. 52.222-22 PREVIOUS CONTRACTS AND COMPLIANCE REPORTS (FEB 1999) 8. 52.222-25 AFFIRMATIVE ACTION COMPLIANCE (APR 1984) 9. 52.225-13 RESTRICTIONS ON CERTAIN FOREIGN PURCHASES (MAR 2005) 10. 1352.239-73 SECURITY REQUIREMENTS FOR INFORMATION TECHNOLOGY RESOURCES (OCT 2003)11. 1352.239-74 SECURITY PROCESSING REQUIREMENTS FOR CONTRACTORS/SUBCONTRACTOR PERSONNEL FOR ACCESSING DOC INFORMATION TECHNOLOGY SYSTEMS (OCT 2003 12. 52.243-1 CHANGES--FIXED-PRICE (AUG 1987) 13. 52.244-6 SUBCONTRACTS FOR COMMERCIAL ITEMS (Dec 2004) 14. 52.252-2 CLAUSES INCORPORATED BY REFERENCE (FEB 1998) **** The Westren Regional Acquisition Division, requires that all contractors doing business with this Acquisition Office be registered with the Central Contractor Registey (CCR) as of October 1, 2003. After this date, NO award can be made unless the vendor is registered in CCR. For additional information and to register in CCR please access the following web site: http//www.ccr.gov . In order to register with CCR and be eligible to receive an award from this Acquisition Office, all offerors must have a Dun & Bradstreet Number (DUN). A DUN number may be acquried free of charge by contacting Dun & Bradstreet on line at www.dnb/eupdate of by phone at (800) 333-0505