SWORD AND SCABBARD

Solictation Number; SPE1C1-15-Q-0077 In addition to price and other related factors, the contracting officer, on this acquisition, may consider past delivery and quality performance as an evaluation factor using the Past Performance Information Retrieval System, and may make an award at other than the lowest evaluated price. *Variation in quantity is +/- 2% *FAR 52.248-01, Alt III Value Engineering is applicable to this award. *Two (2) first articles are due 30 days after date of award. Submit Samples to: DLA Troop Support 700 Robbins Ave. Philadelphia, PA 19111 Attn: Don Howarth Bldg. 3 / WK Station 5108 Note: The government reserves the right to cancel the order if first article samples are not received 30 days after award SWORD AND SCABBARD, NONCOMMISSIONED OFFICER CLASS -2 . ADDITIONAL INFORMATION FOR MIL-S-19206: . PAGE 6, PARA. 3.3.7.2, ADD THE FOLLOWING SENTENCE TO THE END OF THE PARAGRAPH: "THE BLADE SHALL BE HARDENED FULL HARD AND THEN TEMPERED TO SHOW A ROCKWELL "C" SCALE HARDNESS TEST OF 48 TO 53." . PAGE 8, PARA. 3.7.4 LABEL TAG, SECOND SENT- ENCE, DELETE "TYPE VIII" AND SUBSTITUTE "TYPE VI (SIX)". . . AT END OF PARA 3.7.4, ADD "THE LABEL SHALL BE CAUGHT IN THE HEM STITCHING OF FLANNELETTE CASE." . PAGE 8, PARA. 3.9, AT END OF SENTENCE DELETE "BUT LOOSELY.", AND SUBSITUTE "AND IS STATIONARY." . PAGE 11, PARA. 4.5.3.3, PERFORMANCE EX- AMINATION, UNDER "DEFECT", ADD THE FOLLOWING: "BLADE FALLS OUT OF SCABBARD WHEN INVERTED." . PAGE 11, PARA. 4.5.3.3 PERFORMANCE EX- AMINATION, AT THE END OF PARAGRAPH, ADD: CLASSIFICATION OF DEFECT - MAJOR FOR ALL DEFECTS LISTED ABOVE. PAGE 13, PARA 4.5.3, EXAMINATION OF END ITEM, LINE 3 AFTER "CASE." ADD THE FOLLOWING; "THE INSPECTION LEVEL SHALL BE II, AND THE AQL SHALL BE 1.5 FOR MAJOR, 2.5 FOR TOTAL MINOR A AND MINOR B, AND 4.0 FOR TOTAL DEFECTS. '. . PAGE 14, UNDER "DESIGN AND CONSTRUCTION" ADD THE FOLLOWING DEFECT: "HILT GUARD OF INSUFFICIENT THICKNESS TO CUSHION EFFECT OF OF IMPACT WHEN SLIDING SWORD STRIKES UPON SCABBARD.", AND UNDER "CLASSIFICATION" ADD "'MINOR A". . PAGE 15, UNDER "DESIGN AND CONSTRUCTION" DEFECT NUMBER 7 (BLADE HAS MORE...), LINE 2, DELETE "" AND ADD "ON EACH SIDE." . PAGE 16, AT BOTTOM OF PAGE ADD NEW DEFECT CATA- GORY: UNDER "EXAMINE" ADD "FLANNELETTE CASE", UNDER "DEFECT" ADD "NAPPED SIDE NOT ON INSIDE OF CASE.",UNDER "CLASSIFICATION", ADD "MINOR A". . PAGE 17, PARA. 4.5.3.3 PERFORMANCE EXAMINATION, ADD THE FOLLOWING DEFECTS: - "SWORD FALLS OUT OF SCABBARD WHEN INVERTED AT MORE THAN 40 DEGREES." - "SWORD IS NOT STATIONERY, I.E. WIGGLES, MOVES, RATTLES WHEN INSERTED INTO SCABBARD." ADD NEW COLUMN: "CLASSIFICATION OF DEFECT". LIST ALL DEFECTS AS "MAJOR". . BAR CODE LABEL/TAG FOR MIL-S-19206. EACH ITEM SHALL BE INDIVIDUALLY BAR CODED. THE BAR CODE ELEMENET SHALL BE A 13 DIGIT NATIONAL STOCK NUMBER (NSN). THE BAR CODE FOR NSN SHALL BE A MEDIUM TO HIGH DENSITY, CLEARLY LEGIBLE AN READABLE BY SCANNER, AND SHALL BE LOCATED SO THAT THEY ARE COMPLETELY VISIBLE ON THE ITEM WHEN PACKAGED AS SPECIFIED. ATTACHMENT OF THE LABEL SHALL CAUSE NO DAMAGE TO THE ITEM. THE LABEL SHALL BE POSITIONED FOLDED AND SHALL BE TYPE VI OF MIL-STD-32075. BAR CODE DEFECTS: -BAR CODE OMITTED OR NOT READABLE BY SCANNER- MINOR. HUMAN READABLE INTERPRETATION (HRI) OMITTED- MINOR. -NOT VISIBLE ON FOLDED, PACKAGED ITEM-MINOR. -CAUSE DAMAGE TO THE ITEM-MAJOR. ADDITIONAL INFORMATION FOR A-A-52094A: NO ADDITIONAL INFORMATION (ref. T1481) ADDITIONAL INFORMATION FOR QQ-W-321: . QQ-W-321D IS CANCELLED AND REPLACED BY ASTM B-134, ASTM B-159, ASTM B-159M, ASTM B-206 AND ASTM B-206M. . MIL-DTL-32075: LABEL FOR CLOTHING, EQUIPAGE, AND TENTAGE, GENERAL USE REPLACES DDD-L-20 (Ref. T0451 - June 19, 2007) INTERIM SPECIFICATION CHANGES TO MIL-DTL-32075: PAGE 4, PARA. 3.3.5, AFTER "TYPE III OR IV, CLASS 4 OF" DELETE "DDD-L-20" AND REPLACE "MIL-DTL-32075,". PAGE 6, TABLE I, "PHYSICAL REQUIREMENTS OF THE TYPE VI FINISHED LABEL." UNDER "TEARING STRENGTH" DELETE: "(LB.) MINIMUM" AND SUBSTITUTE: "(GNS) MINIMUM." PAGE 12, PARA 3.3.2.17, AFTER "NSN" ADD "AND THE UNIVERSAL PRODUCT CODE (UPC) SUPPLIED BY THE GOVERNMENT, FOR ALL NSNs." ADDITIONAL INFORMATION FOR DDD-T-86: . INTERIM CHANGES TO DDD-T-86H: . NOTE - REDUCED AQLS APPLY AS FOLLOWS: PAGE 9, LINE 9, DELETE "0.4" AND SUBSTITUTE, "0.28", FOR MAJORS. DELETE "1.5" AND SUBSTITUTE "1.0", FOR TOTALS. . COMMERCIAL ITEM DESCRIPTION A-A-52071 DATED 25 APRIL 1990 HAS BEEN AUTHORIZED FOR USE IN PLACE 0F DDD-T-86H. "THE REQUIREMENT FOR THE HERRINGBONE TAPE IS TYPE I, 3/16 INCH WIDTH AND 58 PICKS PER INCH FROM TABLE I. PHYSICAL REQUIREMENTS." ADDITIONAL INFORMATION FOR MIL-F-10336: . MIL-F-10336 IS CANCELLED. USE ASTM D 710 . ADDITIONAL INFORMATION FOR FED-STD-191: FED-STD-191A NOTICE 7, DATED AUGUST 9, 2000 IS HEREBY INACTIVE FOR NEW DESIGN. WHEN NOT USING FED-STD-191, SEE INTERIM CHANGES TO END ITEM SPECIFICATION FOR REPLACEMENT ASTM. INTERIM CHANGES TO FED-STD-191A: TEST METHOD 5202, PARA. 5.3, DELETE FIRST SENTENCE AND SUBSTITUTE: "THE SPECIMEN SHALL BE CLAMPED FIRMLY, WITH ONE END FLUSH WITH THE OUTER EDGE OF THE VISE, SUCH THAT ONE INCH OF SPECIMEN LIES WITHIN THE CLAMP AND ONE INCH OF THE SPECIMEN EXTENDS BEYOND THE CENTER OF ROTATION (FACE OF THE VISE), AND WITH THE LONG EDGE PARALLEL TO THE FACE OF THE DIAL PLATE". TEST METHOD 5309.1 ABRASION RESISTANT OF TEXTILE WEBBING. PAGE 1, PARA 4.1.2,LINE 4: DELETE "B-97" AND SUBSTITUTE "B-91". THE FOLLOWING METHODS ARE IDENTIFIED AS SPECIFYING OZONE DEPLETING SUBSTANCES: 1100, 1200, 1240, 1400, 1410, 1500, 1510,1520,1530, 1540, AND 1550. PARA 5.1 OF THESE TEST METHODS REQUIRE THE USE OF 1,1,1- TRICHLOROETHANE, ALCOHOL OR ETHER. 1,1,1-TRICHLORETHANE IS AN OZONE DEPLETING SUBSTANCE (METHYL CHLOROFORM) AND IS THEREFORE PROHIBITED. THE USE OF EITHER ALCOHOL OR ETHER IS REQUIRED WHEN THESE METHODS ARE IN BASIC OR ANY REFERENCED DOCUMENT. METHOD 5202, STIFFNESS OF CLOTH, DIRECTIONAL; CANTILEVER BENDING METHOD. PAGE 2, PARA. 5.3 DELETE FIRST SENTENCE AND SUBSTITUTE WITH THE FOLLOWING: "THE SPECIMEN SHALL BE CLAMPED FIRMLY, WITH 1 END FLUSH WITH THE OUTER EDGE OF THE VISE, SUCH THAT 1" OF THE SPECIMEN LIES WITHIN THE CLAMP AND 1" OF THE SPECIMEN EXTENDS BEYOND THE CENTER OF ROTATION (INNER FACE OF THE VISE) AND WITH THE LONG EDGE PARALLEL TO THE FACE OF THE DIAL PLATE." METHOD 5556.1, MOBILE LAUNDRY EVALUATION FOR TEXTILE MATERIALS, PAGE 5, PARA. 5.2.2, LINE 8: DELETE SENTENCE BEGINNING WITH "THE SPECIMENS AND BALLAST" IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING: "THE SPECIMENS AND BALLAST SHALL BE SEPARATED, OPENED TO FULL WIDTH AND PLACED IN A PRE-HEATED DRYER HAVING A STACK TEMPERATURE OF 140-180 DEG. F. THIS TEMPERATURE RANGE CORRESPONDS TO A SETTING OF "HIGH" ON THE TEMPERATURE INDICATOR ON THE DRYER. DRYING SHALL CONTINUE FOR 45-60 MINUTES OR UNTILSAMPLES ARE DRY IN A ROTATING TUMBLE DRYER." PAGE 5, PARA. 5.2.3, LINE 8: DELETE SENTENCE BEGINNING WITH "THE SPECIMENS AND BALLAST" IN ITS ENTIRETY AND SUBSTITUTE WITH THEFOLLOWING: "THE SPECIMENS AND BALLAST SHALL BE SEPARATED, OPENED TO FULL WIDTH AND PLACED IN A PRE-HEATED DRYER HAVING A STACKTEMPERATURE OF 140-180 DEG. F. THIS TEMPERATURE RANGE CORRESPONDS TO A SETTING OF "HIGH" ON THE TEMPERATURE INDICATOR ON THE DRYER. DRYING SHALL CONTINUE FOR 35-40 MINUTES OR UNTIL SAMPLES ARE DRY." METHOD 5931, ELECTROSTATIC DECAY OF FABRICS; DETERMINATION OF PAGE 1, PARA. 3: AFTER NUMBER OF DETERMINATIONS ADD "PER SAMPLE UNIT". PAGE 1, PARA. 4: DELETE "APPARTUS" AND SUBSTITUTE "APPARATUS". PAGE 1, PARA. 5.1, LINE 3: AFTER "AT" DELETE"APPROXIMATELY". PAGE 2, PARA. 5.2, LINES 2, AND 5: AFTER "OF" ADD "+-". LINE 6: AFTER "TO" ADD "+-". PAGE 2, PARA. 5.3: DELETE IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING:"5.3 MOUNT A SPECIMEN TIGHTLY ACROSS THE ELECTRODES, CENTERING IT OVER THE SENSOR OPENING. THE SURFACE OF THE TEST SPECIMEN (BACK OR FRONT) SHALL FACE THE SENSOR. RECORD (OPTIONAL) THE RESIDUAL CHARGE LEVEL ON THE SAMPLE AS SEEN BY THE SENSOR, INCLUDING POLARITY. NOTE THAT TEST SAMPLES WITH THE RESIDUAL CHARGE LEVELS OF LESS +500 VOLTS YIELD THE BEST RESULTS. APPLY +5000 VOLTS TO THEELECTRODES FOR A PERIOD OF 20 SECS. AT THE END OF THE 20 SECOND PERIOD, THE HIGH VOLTAGE (5000 VOLTS) SHALL BE TURNED OFF ANDTHE SPECIMENS IMMEDIATELY GROUNDED. THE VOLTAGE BEHAVIOR OF THE SPECIMEN WITH RESPECT TO TIME SHALL BE PLOTTED ON THE RECORDER. NOTE: IN SOME CASES, THE TEST EQUIPMENT WILL DISPLAY VOLTAGE AND DECAY TIME INFORMATION AND A CHART RECORDER IS NOT NECESSARY." PAGE 2, PARA. 5.4, LINE 3: DELETE SENTENCE BEGINNING WITH "IF THE SPECIMEN DID" IN ITS ENTIRETY. PAGE 2, PARA. 5.5: DELETE PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING: "RECORD THE MAXIMUM VOLTAGE LEVEL(INCLUDING POLARITY) AND DECAY TIME TO 10% OF THE MAXIMUM VOLTAGE LEVEL ACHIEVED." PAGE 2, PARA. 5.6, LINE 1: ADD THE FOLLOWING PRIOR TO 1ST SENTENCE: "REVERSE VOLTAGE POLARITY REPEAT MEASUREMENT, ANDRECORD RESULTS." PAGE 3, PARA. 6.6: DELETE PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING: "THE AVERAGE TIME TO DECAY TO 10%OF THE MAX VOLTAGE SHALL BE INCLUDED FOR EACH OF THE WARP & FILLING DIRECTIONS, AS WELL AS THE OVERALL AVERAGE, FOR EACHFABRIC TESTED. THESE WILL BE OBTAINED BY AVERAGING THE TEST RESULTS (ABSOLUTE VALUE OF) TOGETHER FOR BOTH VOLTAGEPOLARITIES. UNLESS OTHERWISE STATED IN THE REQUIREMENTS DOCUMENT, THE FABRIC SHALL BE CONSIDERED ACCEPTABLE IF THEAVERAGE MAXIMUM VOLTAGE IN BOTH THE WARP AND FILLING DIRECTIONS IS LESS THAN 4000 VOLTS, AND THE AVERAGE DECAY TIME (TO 10% MAXVOLTAGE) IS GREATER THAN 0.5 SECONDS IN BOTH THE WARP AND FILLING DIRECTIONS. IT SHALL BE INDICATED WHETHER THE FABRIC ISACCEPTABLE OR NON-ACCEPTABLE." PAGE 3, PARA. 7.1, SECOND COLUMN, LINE 2: DELETE 406C AND SUBSTITUTE WITH "406D". AFTER PARA. 7.1, ADD THE FOLLOWING: "7.2 NOTE: IF THE MODEL 406D STATIC DECAY METER, OR EQUIVALENT, IS USED, A CHART RECORDER ISNOT MANDATORY FOR THE TEST." (Ref. T0215) ADDITIONAL INFORMATION FOR FED-STD-311: INTERIM CHANGES FROM FED-STD-311: INTERIM CHANGE FROM CH NOT 1, 8/27/71: SECTION 4, PARA. 4.5.1.2, LINE 8: DELETE THE PERIOD AFTER "BACKBONE" AND ADD "AND TO INDICATE THE ROOT OF THE TAIL". INTERIM CHANGE FROM TEST METHOD 7011.1: PARA. 4.1.2: DELETE ENTIRELY AND SUBSTITUTE THE FOLLOWING: "4.1.2 INDICATING DEVICE. THE INDICATING DEVICE SHALL BE EITHER OF THE KINDS LISTED BELOW. 4.1.2.1 THE SHRINKAGE METER DIAL. A DIAL INDICATOR HAVING A FACE DIVIDED INTO 360-380 DEGREES, WITH ONE REVOLUTION OF THE DIAL HAND CORRESPONDING TO 0.5 INCHES (12.7 MM) SPECIMEN MOVEMENT, WITH LEEWAY FOR FOUR REVOLUTIONS. 4.1.2.2 AGD DIAL INDICATOR. A MECHANICAL DEVICE CAPABLE OF REGISTERING ON A SCALE READING OF THE SHRINKAGE OR SWELLING RATIO OF THE SPECIMEN IN A RATIO OF 25 UNITS OF DIAL MOVEMENT TO ONE UNIT OF SPECIMEN MOVEMENT, OR GREATER, AND SHALL ACCURATELY DETECT THE POINT AT WHICH SHRINKAGE BEGINS BY THE MOVEMENT OF THE DIAL NEEDLE. THE INDICATOR SHALL HAVE A SPINDLE CAPABLE OF ATTACHMENT TO THE SPECIMEN AND TO THE ADJUST- ABLE WEIGHT ASSEMBLY (SEE 4.1.11)." PARA. 4.1.3: DELETE "HEATING COIL" AND INSERT "IMMERSION HEATER". PARA.7.1: DELETE ENTIRELY AND SUBSTITUTE THE FOLLOWING: "7.1 THE THERMOMETERS MAY BE PURCHASED FROM THE THOMAS SCIENTIFIC CO. OR FISHER SCIENTIFIC CO., EACH HAVING REGIONAL OFFICES. 7.2 DIAL INDICATORS MAY BE PURCHASED FROM B. C. AMES CO., LEXINGTON STREET, WALTHAM, MA 02254." (ref. T0211 - 5/23/06) INSPECTION OF SUPPLIES SHALL BE IN ACCORDANCE WITH FAR PART 52.246-2 STANDARD INSPECTION. ADDITIONAL INFORMATION FOR MIL-STD-105E: MIL-STD-105E, dated 10 May 1989, is hereby canceled. Future acquisitions may refer to: MIL-STD-1916, "DoD Preferred Methods for Acceptance of Product," or ANSI/ASQ Z1.4, "Sampling Procedures and Tables for Inspection by Attributes." Users are cautioned to evaluate these documents for their particular application before citing it as a replacement document. (Copies of MIL-STD-1916 are available online at http://assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) (Copies of ANSI/ASQ Z1.4 are available online at www.asq.org or ASQ Distribution Center, 5131 S. Third Street, Milwaukee, Wisconsin 53207-6028.) MIL-STD-129 CURRENT REVISION UNLESS OTHERWISE SPECIFIED - DEPARTMENT OF DEFENSE STANDARD PRACTICE ,,,,,, - MILITARY MARKING FOR SHIPMENT AND STORAGE ,,,,,, INTERIM CHANGES: OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE: THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T ITEMS, REGARDLESS OF MODE OF SHIPMENT. IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING LIST HERE" SHALL BE STENCILED, NOT HAND LETTERED, ON THE CONTAINER. MIL-STD-147 IS HEREBY REINSTATED AS FOLLOWS: MIL-STD-147E DEPARTMENT OF DEFENSE 16 MAY 2008 STANDARD PRACTICE PALLETIZED UNIT LOADS STANDARDS (COMMERCIAL) ASME-MH1 American Society of Mechanical Engineers (ASME) Pallets, Slip Sheets, and Other Bases For Unit Loads, for construction of pallets. MIL-STD-731 IS HEREBY CANCELLED, NOTICE 2 DATED 12/5/95. ASTM-D-6199 - "STANDARD PRACTICE FOR QUALITY OF WOOD MEMBERS OF CONTAINERS AND PALLETS" HAS BEEN ADOPTED AS A REPLACEMENT AS OF 7/29/98. (ref. T0340 - May 18, 2006) ADDITIONAL INFORMATION FOR ANSI/ASQC Z1.4: NOTE: THE MOST RECENT VERSION OF THIS DOCUMENT SHOULD BE USED. APPLICATION FOR COPIES SHOULD BE ADDRESSED TO: AMERICAN SOCIETY FOR QUALITY 600 NORTH PLANKINTON AVENUE MILWAUKEE, WISCONSIN 53203 (Ref. T0795 - May 17, 2006) IT IS RECOMMENDED THAT TWO EACH FIRST ARTICLE SAMPLES OF THE END ITEM(S) BE SUBMITTED TO THIS CENTER FOR VISUAL, DIMENSIONAL AND SHADE EXAMINATIONS. THIRTY DAYS WILL BE REQUIRED TO EXAMINE AND EVALUATE THE SAMPLES AND TO FURNISH THE RESULTS AND DIRECTIONS REGARDING PRODUCTION TO THE CONTRACTOR. DD 22571 P-230 REV A 6/12/1973 MC FIGURE 2A 7/6/1969 PRES/PACK LEVELS SHALL BE A/C IN ACCORDANCE WITH MIL-S-19206E. QUANTITY UNIT PACK SHALL BE IN ACCORDANCE WITH MIL-S-19206E SIGNIFICANT NOTE - "PALLETIZATION IS REQUIRED FOR THESE SUPPLIES". NOTE: THE FOLLOWING APPLIES TO ALL NON-MANUFACTURED WOOD PACKAGING MATERIALS: "All Wood Packaging Material (WPM) acquired by DOD must meet requirements of International Standards for Phytosanitary Measures (ISPM) 15, "Guidelines for Regulating Wood Packaging Materials in International Trade." DOD shipments inside and outside of the United States must meet ISPM 15 whenever WPM is used to ship DOD cargo, or when wood is being acquired by DLA for future use as packaging material. WPM is defined as wood pallets, skids, load boards, pallet collars, wooden boxes, reels, dunnage, crates, frame and cleats. Packaging materials exempt from the requirements are materials that have undergone a manufacturing process, such as corrugated fiberboard, plywood, particleboard, veneer, and oriented strand board (OSD). All WPM shall comply with one of the following official quality control programs: Heat Treatment (HT) or Kiln Dried Heat Treatment (KD HT) in accordance with American Lumber Standard Committee, Incorporated (ALSC) Wood Packaging Material Program and WPM Enforcement Regulations (see http://www.alsc.org/; or All WPM shall include certification/quality markings in accordance with the ALSC or NWPCA standards, as applicable. Markings shall be placed in an unobstructed area that will be readily visible to inspectors. Pallet markings shall be applied to the stringer or block on diagonally opposite sides of the pallet and be contrasting and clearly visible. All containers shall be marked on a side other than the top or bottom, contrasting and clearly visible. All dunnage used in configuring and/or securing the load shall also comply with ISPM 15 and be marked with an ASLC approved DUNNAGE stamp. Failure to comply with the requirements of this restriction may result in refusal, destruction, or treatment of materials at the point of entry. The Agency reserves the right to recoup from the Contractor any remediation costs incurred by the Government." PALLET SHALL BE 4 WAY ENTRY, WINGED TYPE. PALLETIZED LOAD DIMENSIONS SHALL NOT EXCEED 43 INCHES IN LENGTH, 52 INCHES IN WIDTH, AND 54 INCHES IN HEIGHT (INCLUDING THE PALLET). THE PALLETIZED LOAD SHALL BE BONDED USING APPROVED COMMERCIAL BONDING MATERIALS. THE USE OF METAL BANDING, IN SECURING BOXES TO PALLETS, IS DISCOURAGED. PALLET LOADS SHALL CONTAIN THE SAME NUMBER OF CARTONS, OF IDENTICAL QUANTITIES, OF ONE NSN, TO THE MAXIMUM EXTENT POSSIBLE. PALLET LOADS CONTAINING MORE THAN ONE NSN SHALL BE CLEARLY MARKED TO LIST ALL THE NSN'S CONTAINED IN THE LOAD. NO CARTON SHALL HAVE MORE THAN ONE NSN. AT THE END OF A SIZE RUN, NO MORE THAN ONE CARTON PER NSN MAY BE SHORT OR OVER THE SPECIFIED QUANTITY. SAID CARTON SHALL BE CLEARLY MARKED "SHORT" OR "OVER". MIL-STD-147 IS REFERENCED FOR PALLETIZED LOADS. IN ADDITION TO REQUIREMENTS SPECIFIED ABOVE THE FOLLOWING CLAUSE ALSO APPLIES: 52.247-9012 - REQUIREMENTS FOR TREATEMENT OF WOOD PACKAGING MATERIALS (WPM) - (JULY 2006) NOTE: WHEN THE CONTRACT OR DELIVERY QUANTITY SUPPORTS THE USE OF A PALLET, PALLETIZATION REQUIREMENTS SHALL APPLY. IAW BASIC SPEC NR MIL-S-19206E REVISION NR E DTD 10/03/2006 PART PIECE NUMBER: IAW REFERENCE SPEC NR MIL-DTL-32075 REVISION NR DTD 10/03/2006 PART PIECE NUMBER: IAW REFERENCE STD NR MIL-STD-105E NOT 3 REVISION NR E DTD 10/03/2006 PART PIECE NUMBER: IAW REFERENCE STD NR MIL-STD-129R REVISION NR R DTD 02/18/2014 PART PIECE NUMBER: IAW REFERENCE STD NR MIL-STD-147E(1) REVISION NR E DTD 12/23/2013 PART PIECE NUMBER: IAW REFERENCE STD NR MIL-STD-731A(1) NOT 3 REVISION NR A DTD 10/03/2006 PART PIECE NUMBER: IAW REFERENCE CID A-A-52094A REVISION NR A DTD 10/03/2006 PART PIECE NUMBER: IAW REFERENCE UNK DDD-T-86H NOT 1 REVISION NR H DTD 10/03/2006 PART PIECE NUMBER: IAW REFERENCE UNK FED-STD-191A(6) NOT 7 REVISION NR A DTD 10/03/2006 PART PIECE NUMBER: IAW REFERENCE UNK FED-STD-311(3) REVISION NR DTD 10/03/2006 PART PIECE NUMBER: IAW REFERENCE NON GOVT STD ANSI/ASQC Z1.4-2008 REVISION NR DTD 10/21/2010 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 22571 P230 REVISION NR A DTD 06/13/1973 PART PIECE NUMBER: