Request for quote. Please state your price, your very best delivery and the country of origin. Please respond by email to
[email protected]. These orders are for the GSA warehouse and all clauses that normally apply to our warehouse orders are applicable, including bar code marking and the Buy American Act which can be found at Federal Acquisition Regulations 25.001.Procurement History – Easco Hand Tools $165.28 5130-00-357-5135 UI: SE Qty 289 WRENCH SET, SOCKET: DESCRIPTION In accordance with American Society of Mechanical Engineers (ASME) B107.2-1992. Socket set shall consist of the following 16 components. Tools in the set shall be manufactured by no more than two manufacturers. EXCEPTION(S) TO TECHNICAL DOCUMENT ANSI B107.4. Table 7. Column 5, Af dimensions. For 1/2 inch square drive; delete "0.503 to 0.508" and substitute "0.503 to 0.511". For 3/4 inch square drive; delete "0.753 to 0.758" and substitute "0.753 to 0.761". For 1 inch square drive; delete "1.004 to 1.009" and substitute "1.004 to 1.012". For 1-1/2 inch square drive; delete "1.505 to 1.510" and substitute "1.505 to 1.520". Unless otherwise specified, each set of tools shall be provided in a durable plastic or metal case. The case shall be capable of protecting the tools throughout the life of the tool set and shall be designed to store the components in an orderly manner. The components shall be secured in such a manner that they will not be damaged, will not freely move around, and will not damage the case (e.g., dings/dents) during shipment and handling. The case shall have at least one shutter hook, snap-type latch, or similar hardware to secure the case in a closed position. The case shall be fitted with at least two hinges or a continuous hinge. The plastic case shall be constructed of a double layer, impact resistant material. The metal case shall be corrosion resistant or have a corrosion resistant coating (e.g., plating, paint) on interior and exterior surfaces. Metal hardware (e.g., hinges, hinge pins, latches, screws) on cases shall be corrosion resistant or have a corrosion resistant plating. Paint shall not be the primary corrosion resistant coating on metal hardware. WRENCHING OPENING REQUIREMENTS: The wrench opening shall conform to ASME B107.17m-1991 except as follows: Paragraph "5 USE", delete and substitute the following: "5 USE The applicable "GO" and "NO GO" gage, as specified herein, shall be aligned, centered, and employed in the wrench openings. The "GO" gage shall be employed in the wrench openings prior to employment of the "NO GO" gage. Wrench openings being inspected using "GO" and "NO GO" gages shall not be deburred with either gage. Wrench openings shall not have rips, tears, broaching, or materials (e.g., slugs, silvers, webs, burrs) which would interfere with the gaging accuracy. Eight point wrenching styles shall be inspected using both alternate sets of four points for each specified inspection. Twelve point wrenching styles shall be inspected using both alternate sets of six points for each specified inspection. For sockets and nut drivers, the wrench opening shall accept the "GO" gage to the wrenching depth specified for the wrench opening and shall not accept the "NO GO" gage to a wrenching depth (excluding chamfer) greater than 0.010 of an inch. For box wrenches, torque adapters, and open end crowfeet, the wrench opening shall accept the "GO" gage such that the "GO" gage passes completely through both sides of the wrench and shall not accept the "NO GO" gage to a wrenching depth (excluding chamfer) greater than 0.010 of an inch. For open end wrenches and open end crowfeet, the gages shall be employed in the wrench opening at the front end of the wrench as distinct from the wrench opening at the top and bottom of the wrench. The gages shall be employed using the side of the gage as distinct from the end of the gage. The wrench opening shall accept the "GO" gage such that at least four flats of the "GO" gage do not extend beyond the tips of the wrench. The wrench opening shall not accept the "NO GO" gage to a wrenching depth (excluding chamfer) greater than as follows: NOMINAL WRENCH OPENING SIZES: Less than 19 mm and Less than 3/4 inch - "NO GO" GAGE 0.063 inch NOMINAL WRENCH OPENING SIZES: 19 mm through less than 44 mm and 3/4 through less than 1-3/4 inches - "NO GO" GAGE 0.125 inch NOMINAL WRENCH OPENING SIZES: 44 mm or larger and 1-3/4 inches or larger - "NO GO" GAGE 0.250 inch Reasonable hand force shall be used in the employment of gages. If the gaging results are challenged/disputed based on interpretation of what constitutes reasonable hand force, the issue shall be resolved by employment of the "GO" and "NO GO" gages using the following requirements: The force in pounds (including, when applicable, the weight of the gage and/or the wrench being inspected) in the direction of the wrench opening in the employment of gages shall be as follows: NOMINAL WRENCH OPENING SIZES: Less than 12 mm and Less than 1/2 inch - "GO" GAGE 0 to 4.0 and "NO GO" GAGE 3.5 to 4.0 NOMINAL WRENCH OPENING SIZES: 12 mm through less than 19 mm and 1/2 through less than 3/4 inch - "GO" GAGE 0 to 9.0 and "NO GO" 8.5 to 9.0 NOMINAL WRENCH OPENING SIZES: 19 mm or larger and 3/4 inch or larger - "GO" GAGE 0 to 14.0 and "NO GO" GAGE 13.5 to 14.0 To ensure product acceptance, manufacturers may use gages with tighter dimensional tolerances than those shown herein." A retaining pin and ring shall be provided and secured to each individual socket by means of shrink wrap, plastic bag or similar method. The retaining pin and ring can be one piece design. ITEM MARKING Each item (including all items within a set or kit) shall be marked with the manufacturer's name and identifying symbol, and the state or country of manufacture, unless otherwise specified. All marking shall be engraved, etched, molded, or indented. PACKAGING One (1) item shall be preserved and packaged in a unit package designed to protect the item against damage during shipment, handling, and storage. PACKING The unit packages shall be packed in a close fitting fiberboard box in compliance with the Uniform Freight Classification and the National Motor Freight Classification requirements of Rules, Item 222, Sec. 3., Minimum 200 or ECT 32. MARKING All unit, intermediate, transport packages and unit loads shall be marked and bar coded for delivery to civilian activities in accordance with FED-STD-123G, dated June 6, 1997, or marked and bar coded for delivery to military activities in accordance with MIL-STD-129N, dated 15 May 1997, as applicable. PALLETIZATION Pallet Configuration: The pallets shall be 48-inch length x 40-inch width, general purpose, four-way entry, flush stringer, double-face non-reversible pallets. Pallet lumber used shall be bark free. Pallet Load Size: The load plus the pallet shall have a maximum height of 53 inches and shall not exceed 2500 pounds in weight. Pallet Load Configuration: The containers or items shall be placed in a suitable pattern to form a stable and balanced load. Palletized loads shall be secured to the pallet to insure that the load arrives intact. Stacking Strength: The pallet plus the load shall be capable of supporting three additional like loads without any product damage and without the load or the pallet collapsing. Vertical, horizontal, or filler reinforcement may be added as necessary to provide strength. Partial Palletized Loads: Less than one-half pallet loads shall not be used for stacking, unless load is balanced on pallet. The partial palletized load shall be used for top loading only.